Membuat Simulasi Jaringan Router OSPF Part 4 (Cisco Packet Tracer)

Masih melanjutkan Postingan Sebelumnya Tentang Membuat Simulasi Jaringan Router OSPF ,dan ini merupakan postingan terakhir pembahasan tentang Jaringan Router OSPF.
Pada Postingan Sebelumnya kita telah berhasil membuat Simulasi Jaringan Seperti gambar di bawah ini :


Nah coba kita tes ping dari PC0 ke PC1
ping 192.168.4.2 dan hasilnya
koneksi belum sempurna
Pada Gambar di atas terlihat jelas koneksi masih belum sempurna,sekarang yuk kita setting agar terhubung dengan sempurna.
Sekarang Mari kita setting Router0
klik 2 kali pada Router0 dan masuk pada menu CLI

ok lalu ketikan perintah di bawah ini  :

Router>enable
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

     10.0.0.0/30 is subnetted, 3 subnets
C       10.10.1.0 is directly connected, Serial0/1
C       10.10.4.0 is directly connected, Serial0/0
C       10.10.5.0 is directly connected, FastEthernet1/0
C    192.168.1.0/24 is directly connected, FastEthernet0/0
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#router ospf 90
Router(config-router)#network 10.10.1.0 255.255.255.252 area 9
Router(config-router)#network 10.10.4.0 255.255.255.252 area 9
Router(config-router)#network 10.10.5.0 255.255.255.252 area 9
Router(config-router)#network 192.168.1.0 255.255.255.0 area 9
Router(config-router)#log-adjacency-changes
Router(config-router)#end

%SYS-5-CONFIG_I: Configured from console by console
Router#write
Building configuration...
[OK]

Setting OSPF Roter0

Ok Sekarang Selanjutnya Kita Setting lagi Router1

Router>enable
Router#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

     10.0.0.0/30 is subnetted, 3 subnets
C       10.10.3.0 is directly connected, Serial0/1
C       10.10.4.0 is directly connected, Serial0/0
C       10.10.6.0 is directly connected, FastEthernet1/0
C    192.168.4.0/24 is directly connected, FastEthernet0/0
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#router ospf 90
Router(config-router)#network 10.10.3.0 255.255.255.252 area 9
Router(config-router)#network 10.10.4.0 255.255.255.252 area 9
Router(config-router)#network 10.10.6.0 255.255.255.252 area 9
Router(config-router)#network 192.168.4.0 255.255.255.0 area 9
Router(config-router)#log-adjacency-changes
Router(config-router)#end

%SYS-5-CONFIG_I: Configured from console by console
Router#write
Building configuration...
[OK]

Nah Untuk Setting Router0 dan Router1 Telah Selesai sekarang Mari kita tes Ping dari PC0 ke PC1

ping 192.168.4.2

dan hasilnya
Ada Reply Berarti jaringan telah Sempurna
OK Sekarang temen-temen coba sendiri yah setting Router2 dan Router3,caranya sama seperti langkah2 diatas.

Untuk menentukan Network,perhatikan pada show ip route..!!!

network




Artikel Terkait:


Category Article , ,